Corsair highlights a front panel corsair 4000d case covered in triangle, Corsair’s 4000D airflow PC case has one of the good looking style that delivers what it promises: ample, well, airflow to pc parts cool under pressure.
Priced at a very low $80.00 – $94.99 with a tempered-glass side panel, it’s far from the most packed ATX mid-tower we have seen for below $100.
However its affordability and construction quality build it price a glance if you are buying a spiffy-on-a-budget pc case while saving up for the things inside.
Corsair 4000D Case Specs
|Dimensions (HWD)||17.83 by 9.06 by 18.35 inches|
|Power Supply Mounting Location||Bottom|
|Power Supply Form Factor Supported||ATX|
|Power Supply Maximum Length||300 Meters 220 mm|
|Maximum CPU Cooler Height||170 mm|
|Maximum GPU Length||360 mm|
|Fan Controller Included?||Yes|
|120mm/140mm/200mm Fans Included||2|
|120mm or 140mm Fan Positions||6|
|PCI Expansion Slot Positions||7|
|Side Window(s)?||Yes (Tempered Glass)|
|Front Panel Ports||USB 3.0, headphone, USB 3.1 Type C|
|Internal 2.5-Inch Bays||2|
|External 3.5-Inch Bays||0|
|Internal 3.5-Inch Bays||2|
|External 5.25-Inch Bays||0|
|Motherboard Form Factors Supported||MicroATX, Mini-ITX, ATX|
The Design: Triangles All the way Down
Additionally, to incorporating that perforated front panel, Corsair additionally left massive gaps on either side of this perforated section that allow extra inward ventilation.
The top is additionally perforated and covered by an outsized magnetic dust filter, and also the back of the case has ventilation holes cut in it from top to bottom.
Altogether, this makes for a transparent path of low resistance for air to pass straight through the case. 2 120mm Corsair AirGuide fans are pre-mounted (one front, one back) to push things on.
The two sides of the chassis are not quite as friendly in the airflow department.
The corsair 4000d case panel is a solid sheet of steel, and the left panel is tempered glass, without any cut-throughs for airflow in or out on both sides.
This should not hamper cooling much, however, thanks to the abundance of ventilation elsewhere and also the front-to-back style.
On the inside of the Corsair 4000d case, the perforations continue.
Like several different trendy chassis, the 4000D airflow is broken up into 2 main compartments.
The higher compartment holds the motherboard, whereas the lower compartment is walled off behind a shroud that holds the ability to offer and has room for storage devices.
Not like on most rival cases, though, the metal sheet separating these 2 areas is roofed in the same triangular perforations seen on the front of the case.
This should help to stay the power offer comparatively cool. In most such case styles, the supply gets isolated and needs to argue itself in terms of air through the bottom panel.
The rear panel has 2 slots for vertical GPU mounting alongside the seven PCI-specific card positions.
Like in most cases, however, the vertical-mounting hardware and also the necessary GPU riser cable aren’t included; you’ll need to seek out these yourself.
A Look at the Front I/O
A budget case goes to indicate its stripes in places, and the loadout of ports is one in every of them here.
The front I/O panel of the Corsair 4000D PC case leaves a small amount to be wish.
This panel is very bare by trendy standards, with only 1 USB 3.0 Type-A port and one USB 3.1 Type-C port. additionally present are a headphone/microphone combo jack and also the usual reset and power buttons. That’s it.
As prevalent as USB devices are these days, we can all agree that simply 2 USB ports are not extreme enough for many of us.
Really, this arrangement is commonly like having only 1 USB port, because not several devices have a USB cable with Type-C connectors on each end.
We expect Corsair should have sprung for the additional port up here or created each USB Type-A.
The Building experience
Building a system into the Corsair 4000D pc case is a predictable experience and a lot of good than a negative.
The most notable issue I found is that the chassis’ facet panels are neither simple to remove nor to reattach.
This can be most notable with the solid metal right-side panel of my take a look at sample.
While obtaining it and the glass left panel on and off takes some finesse, it’s possible with practice. Hopefully, you will not have to do it much, once your build is finished.
Fitting the motherboard into place is simple enough, as there is very little in the way to block the board’s installation.
However, this can be positioned so much enough forward that it should not get in the means of putting in the motherboard after getting the motherboard mounted in the case.
I measured just below 1.5 inches of room between the edge of the quality and best ATX motherboard that I used and this opening, which created plugging in SATA cables quite easily.
I could, however, have finished more clearance at the top of the case.
Corsair 4000D EXP
Right now, it’s in a little of a grey zone—The case is open enough that you can access ports on the top of the motherboard and even toss in a top-mounted fan or 2.
However liquid coolers and their thick sandwiches of radiators and fans can likely get in the way of connecting headers up during this area.
You will need to do any fine wiring in this neighborhood before tackling the liquid cooling.
None of this is to say that you cannot add a liquid cooler to the top of the case.
However, it’d most likely be a better idea to mount the cooler in the front of the case instead.
If you are doing prefer to mount it on the top, you should add it last, when you get the motherboard absolutely installed and rigged.
Later tweaks might mandate removing the radiator.
Corsair added room in this case for a complete of 4 storage devices.
On the hidden side of the motherboard mounting tray are 2 2.5-inch drive mounts, and at the lowest of the case is a drive cage that can hold 2 3.5-inch or 2.5-inch drives.
You also get a fan controller set behind the motherboard mounting tray. the 2 Corsair fans provided are wired into this controller box.
Corsair also added a nifty channel with Velcro ties that helps to stay cables neat and arranged.
This sits directly beside the cable in the tray, making it convenient for running cables to devices on every side of the board…
We’ve seen similar cable-routing comforts from vendors like NZXT recently, like in the recently reviewed (and far more expensive) NZXT H710i.
This type of channeling should be customary equipment.
Verdict: stepping into Your Flow Zone can be low cost
Though it’s a couple of limitations, Corsair’s 4000D airflow is overall a fine budget-to-midrange case.
Building an uncomplicated cool system inside it was principally free of hurdles.
The case might not be the most original of styles, however it will look nice when kitted out with a complement of elements and RGB lights, (Three front-panel RGB or ring-style fans would very shine.)
Last however not least, the case is fairly priced.
We’ve reviewed alternative cases in this value vary that have scored solid marks, as well as the Deepcool CL500, the Deepcool GamerStorm Macube 310P, and therefore the close up Pure Base 500.
The 4000D airflow case rates more or less with the Macube 310P and easily behind the CL500 and Pure Base 500.
Ultimately, all of those are shut enough to 1 another that choosing whichever case tickles your DIY aesthetic best is that the way to go—or, failing that, the one that’s the lowest-priced at the time of your purchase.